11 replies to this topic

[dufrain]

I just got my first machine to sit in front of my Atv sales place. Its a Vendo 511 according to the plate on the side.It says Vmax inside so I dont know. It works fine on cans but I dont exactly know how to set it to vend bottles,Im wanting to do 24oz.Singe stack will be fine for my small volume. I dont know how to adjust the cams or anything so If someone here is familiar with this type machine please let me know. Thanx

[snack dude]

I just got my first machine to sit in front of my Atv sales place. Its a Vendo 511 according to the plate on the side.It says Vmax inside so I dont know. It works fine on cans but I dont exactly know how to set it to vend bottles,Im wanting to do 24oz.Singe stack will be fine for my small volume. I dont know how to adjust the cams or anything so If someone here is familiar with this type machine please let me know. Thanx

I have not set a V-max up for 24 oz bottles but I have for 20 oz bottles and monster energy drinks so this should work.
1. after opening the machine, below the slots where the drinks sit remove the metal cover that covers the motors for each slot.
2. Empty the cans out of each slot and to the right of each motor there will be a small metal tip with a cotter pin in it. remove the cotter pin and reach inside the slot and remove the piece of metal or shim from the slot. This shim is for cans not bottles.
3. Underneath and to the left of each motor is another cotter pin and three small holes. ( Since the machine is set for cans the bar underneath each slot is probably sitting in the middle hole. remove the cotter pin and reach underneath the slots and move the bar to the hole on the left.
4. On the face of the motor slighly lift up the outer tab and spin it to the #1 setting. This will allow you to single stack your bottles. #2 would be for two deep and so on.
5. Slide the depth bar up to the depth of the 24oz bottle

Your Done

Lst me know if you have any questions.

[dufrain]

Thanx for the reply,I got part of it figured out ,I had the metal shim out and the depth bar slid up to the bottle.. One question, how much clearance should i have from the end of the bottle and the depth bar.

I have not set a V-max up for 24 oz bottles but I have for 20 oz bottles and monster energy drinks so this should work.
1. after opening the machine, below the slots where the drinks sit remove the metal cover that covers the motors for each slot.
2. Empty the cans out of each slot and to the right of each motor there will be a small metal tip with a cotter pin in it. remove the cotter pin and reach inside the slot and remove the piece of metal or shim from the slot. This shim is for cans not bottles.
3. Underneath and to the left of each motor is another cotter pin and three small holes. ( Since the machine is set for cans the bar underneath each slot is probably sitting in the middle hole. remove the cotter pin and reach underneath the slots and move the bar to the hole on the left.
4. On the face of the motor slighly lift up the outer tab and spin it to the #1 setting. This will allow you to single stack your bottles. #2 would be for two deep and so on.
5. Slide the depth bar up to the depth of the 24oz bottle

Your Done

Lst me know if you have any questions.

[snack dude]

Thanx for the reply,I got part of it figured out ,I had the metal shim out and the depth bar slid up to the bottle.. One question, how much clearance should i have from the end of the bottle and the depth bar.

It should not be tight. Just enough space to let the bottles slide down freely.

[Technivend]

I just got my first machine to sit in front of my Atv sales place. Its a Vendo 511 according to the plate on the side.It says Vmax inside so I dont know. It works fine on cans but I dont exactly know how to set it to vend bottles,Im wanting to do 24oz.Singe stack will be fine for my small volume. I dont know how to adjust the cams or anything so If someone here is familiar with this type machine please let me know. Thanx

Here is a setup sheet for 20oz in the V-max

http://www.vendoco.c...psiswirltop.pdf

[karmstrong]

The Vendo website has changed but you can go there and look for a manual and they do have setups there.

[dufrain]

I couldnt find any documents there besides for the current models

The Vendo website has changed but you can go there and look for a manual and they do have setups there.

[karmstrong]

I couldnt find any documents there besides for the current models

you can email me at Karmstrong at globalvendinggroup.com and i could get a manual over to you. it does have teh setups in there for some bottles.

[dufrain]

I emailed you ,thanx for the help

[karmstrong]

I emailed you ,thanx for the help

I will get that manual out to you on monday when i get in the office. I just got back from camping. Great time and great weather. Has alot of cleaning to do.
Send that out to you on monday.

[dufrain]

Thanx alot I really appreciate it.

[dufrain]

i never did get the manual