6 replies to this topic

[snackon]

I HAVE A D/N 501E SLOT #1 MOVED SHIMS FOR CANS TRIED VENDING CANS GOT STUCK FIGURED OUT WHAT I DID WRONG FIXED SHIMS. BUT NOW WHEN I SELECT TO VEND NOTHING SO I SWAPPED RELAY NOTHING. IT READS TRY OTHER SELECTION ANY THING THAT MIGHT NEED RESET.TRIED TEST VENDING AND IT WORKS BUT NOTHING ELSE WHEN YOU TRY PUSHING THE SELECTION ANY IDEAS THANKS MIKE

[Technivend]

I HAVE A D/N 501E SLOT #1 MOVED SHIMS FOR CANS TRIED VENDING CANS GOT STUCK FIGURED OUT WHAT I DID WRONG FIXED SHIMS. BUT NOW WHEN I SELECT TO VEND NOTHING SO I SWAPPED RELAY NOTHING. IT READS TRY OTHER SELECTION ANY THING THAT MIGHT NEED RESET.TRIED TEST VENDING AND IT WORKS BUT NOTHING ELSE WHEN YOU TRY PUSHING THE SELECTION ANY IDEAS THANKS MIKE

Hey Mike,

Whew, your post is all over the place . We will need some basic information to be able to help.

-Did the column work before you moved the shims around?
-What relay did you swap?
-You say it reads try another selection. is this on a digital display? If so we will need the type of board used in the machine.
-How did you test vend it? What worked when you test vended?

[vend1ng]

I HAVE A D/N 501E SLOT #1 MOVED SHIMS FOR CANS TRIED VENDING CANS GOT STUCK FIGURED OUT WHAT I DID WRONG FIXED SHIMS. BUT NOW WHEN I SELECT TO VEND NOTHING SO I SWAPPED RELAY NOTHING. IT READS TRY OTHER SELECTION ANY THING THAT MIGHT NEED RESET.TRIED TEST VENDING AND IT WORKS BUT NOTHING ELSE WHEN YOU TRY PUSHING THE SELECTION ANY IDEAS THANKS MIKE

Do you have the back spacer shim set right so the cans push the sold out switch? Just a thought.
Vend1ng

[vend1ng]

I HAVE A D/N 501E SLOT #1 MOVED SHIMS FOR CANS TRIED VENDING CANS GOT STUCK FIGURED OUT WHAT I DID WRONG FIXED SHIMS. BUT NOW WHEN I SELECT TO VEND NOTHING SO I SWAPPED RELAY NOTHING. IT READS TRY OTHER SELECTION ANY THING THAT MIGHT NEED RESET.TRIED TEST VENDING AND IT WORKS BUT NOTHING ELSE WHEN YOU TRY PUSHING THE SELECTION ANY IDEAS THANKS MIKE

Also check and see if the first can didn't get hung under the sold out switch. On newer can bottle machines the sold out lever can get hung on the can when you load the first row. You have to make sure the lever gets pushed when starting that first row with cans bottles are not a problem. Just another thought.
Vend1ng

[snackon]

SORRY, YES IT WORKED FINE BEFORE I MOVED THE SHIMS.I TOOK A RELAY OFF ANOTHER MOTOR AND SWAPPED IT OUT WITH ANOTHER NOT THE RELAY.THE BOARD TYPE IS HOPE THIS IS IT D/N PART# 804910980.01 E-PROM381.01. WHEN I PUSHED THE BLUE BOTTON AND WENT THREW MENU TO TEST VEND MOTORS #1 MOTOR SPINS BUT WHEN I PUT MONEY IN NOTHING. SAYS TRY ANOTHER SELECTION EVERYTHING WORKED BEFORE I WEDGED THE CANS I HAVE ALSO MADE SURE SOLD OUT IS PUSHED IN

[Technivend]

SORRY, YES IT WORKED FINE BEFORE I MOVED THE SHIMS.I TOOK A RELAY OFF ANOTHER MOTOR AND SWAPPED IT OUT WITH ANOTHER NOT THE RELAY.THE BOARD TYPE IS HOPE THIS IS IT D/N PART# 804910980.01 E-PROM381.01. WHEN I PUSHED THE BLUE BOTTON AND WENT THREW MENU TO TEST VEND MOTORS #1 MOTOR SPINS BUT WHEN I PUT MONEY IN NOTHING. SAYS TRY ANOTHER SELECTION EVERYTHING WORKED BEFORE I WEDGED THE CANS I HAVE ALSO MADE SURE SOLD OUT IS PUSHED IN

If it worked before you changed the shimming we will have to assume it was shimmed wrong. Do you have other columns that are shimmed for cans that you can compare it with? Did you check the rear spacer like vend1ng mentioned? This could be an easy thing to miss when changing things around. The sold out lever will need to be made and then the interlock switch will need to be tripped to reset the sold out condition. Try emptying the column, taping the sold out lever down, close the door and make a vend. See if you hear the motor run or if you still get an error.

[snackon]

I WENT TRIED EVERY THING TALKED ABOUT.MIKE TOOK MY TIME RESET SHIMS SHUT THE DOOR VENDS LIKE NEW THANKS FOR THE INPUT MIKE